How To Install Cable Wire In House

Download Article

Download Article

Cabling refers to low-voltage cables that bring phone, Idiot box, and net service into your habitation. They are normally coaxial or ethernet cables. Usually these wires are installed when a house is built, merely yous can also retrofit your home with cabling if this wasn't washed during structure. Beginning, plan the locations and route of each cablevision you're installing. Then cut holes in the wall for the distribution panel, where the inside and exterior cables see. Run the cables from this point up to the attic. Then distribute the cables throughout the business firm from the attic. It's a big job, but with patience and cognition, you can tackle it.

1. ane

   Place the rooms that need a cable hookup. Plan the path for your wires before starting any work. First expect at the plan of your house and place the rooms that require a cable hookup. By and large whatsoever rooms that will have a TV, landline phone, or reckoner need i.^[1]

   • Some contractors like to run wires into every room, just in example. That way, if y'all decide you desire a cable hookup in another room afterward, you don't have to run new wires.
   • If you only utilize wifi for your net access, then you won't demand ethernet cables in every room with a computer.

2. 2

   Position the wiring panel in a central location you can hands access. The wiring panel is where all your home's network wires connect and where service providers attach their wires to. For the best location, look for a betoken in your abode that is out of the way and where yous tin hands run wires to. Contractors usually prefer to put these boxes in the basement if you have one, because it's like shooting fish in a barrel to run the wires up through the walls and to other rooms. Another popular option is a laundry room.^[2]

   • Wiring panels can besides be unsightly, so consider locating it in a closet or a room that visitors don't enter.
   • Wiring panels are as well sometimes called structured wiring panels or distribution boxes. Don't get confused if a website or contractor uses one of these terms.

   Advertisement

3. 3

   Identify the route of the wires from your distribution console. Cables ordinarily feed throughout the house from either the attic or the crawlspace under the business firm. Since not all homes take a crawlspace, the attic is a more than pop selection. Go to your wiring console location and brand sure at that place are hollow walls there that you can run wires upward. Most canvas rock walls should exist suitable. Observe a betoken in this surface area that you can feed a wire straight up into the attic from.^[three]

   • Y'all don't demand precise measurements for running these cables. If the cable ends up besides long, y'all can just cut or roll information technology when it reaches the end of its route. The wiring plan gives y'all a general thought of the route the wires will have, and also marks cable locations for future repairs.
   • Check the blueprints of your house for potential routes that you aren't aware of.
   • You tin utilise existing holes in the wall to run cables as long every bit they don't have electric wires running through them. Electrical wires will interfere with the signal. If all the holes have electrical wires, and so you'll have to drill new ones.

4. 4

   Map out where each cable will go from the attic or crawlspace. Cables distribute throughout the business firm from the attic or crawlspace. Brand a plan of all the rooms that need a cable hookup. Then map how each cable volition feed through the attic and at which points they volition enter each room.^[4]

   • Cables usually feed down from the attic within walls. For an easier, but less visually-appealing task, you can likewise cut through the room's ceiling and feed the cable down this style.

5. 5

   Utilize a program to draw a wiring plan if you don't know where to start. If you have trouble drawing up your own diagram or using your home blueprints, search for a software plan to aid. There are many products that allow you lot scan in your dwelling blueprints and plug in which cables you lot want to install. The programs then produce the ideal wiring plan for your abode that y'all tin can follow easily.^[5]

   • Some programs are free and some are paid. Research dissimilar ones to run across which is best for your needs. Don't try to skimp by using a cheap program if it isn't a quality one.
   • Some paid programs offer free trials that you tin use to plan one job. See if a program y'all're interested in offers a trial.

   Advertisement

1. ane

   Turn off the power. While you lot won't be working with alive cables, you volition exist drilling into walls where electrical wires could exist. Stay safe by turning off your home's ability before starting piece of work. Discover your breaker box and plough the main switch off to cut your home's ability.^[vi]

2. ii

   Locate the studs where your wiring panel will be. The wiring console should be between 2 well studs. Observe the studs in the wall by sliding a stud finder along the wall. Marker on the wall where the ii studs are, and work in the space between them.^[seven]

   • If yous don't have a stud finder, tap on the wall. If you hear a hollow audio, there is no stud at this betoken. A sharp, quick sound indicates that you've tapped on a stud. This isn't exact, merely information technology gives you an idea of where the studs are located.

3. 3

   Cut a 4 in (10 cm) by 4 in (10 cm) inspection pigsty between the studs. When y'all've chosen a point for your wiring panel, make certain the wall section has empty infinite behind it with no obstructions. Describe a 4 in (ten cm) by 4 in (ten cm) foursquare on the wall. Then use your drywall saw and cut away this square section. Wait inside with a flashlight for any wires or pipes.^[viii]

   • If yous see pipes or other wires behind the wall, then use a dissimilar section.
   • Don't worry about the damage to your walls. You lot can patch drywall later after the job is done.

4. 4

   Cut abroad the drywall at your distribution point. When you lot've confirmed that there are no obstructions backside this wall, remove this wall section. Use a drywall saw to cut out the wall between the two studs. Start cutting at one of the stud points 2 inches (five.1 cm) down from the ceiling. Cut beyond the wall until you lot reach the other stud. Do the aforementioned for the lesser of the wall. And then cut vertically, connecting the 2 ends of the cuts you fabricated. Remove this section of wall when yous're done cutting.^[9]

   • Drywall can be heavy, so accept a partner nearby to help yous elevator the wall department out.

5. 5

   Install a structured wiring panel to proceed your cables organized. Cables tin just hang on the wall at the distribution betoken, but a wiring panel keeps them organized much ameliorate. If you want a wiring panel, purchase one from a hardware store. And then mount it in the wall section y'all simply cut out.^[10]

   • Agree the wiring panel up against both studs. Then use a power drill to screw the box to both studs. In that location are latches on the box to insert screws through.
   • This job is easier with someone else holding the box upwardly while y'all drill.
   • A wiring panel is optional. If yous desire to save money, you don't have to buy one.

   Advertisement

1. 1

   Drill a 2.v in (half-dozen.four cm) pigsty through the acme ceiling plate. When you open the wall, yous'll run across a woods cake running above the wall section. Use a boring drill bit 2.5 in (vi.4 cm) in diameter. Press it against the ceiling plate and drill through information technology.^[11]

   • If at that place is a floor below the panel that needs cable admission, also drill a hole through the floor plate.
   • Measure the distance from an external wall to the hole you drilled. This will help you find where to drill the attic hole if you tin can't find the point right above the distribution box.

2. 2

   Drill a hole in your attic floor plate straight above the distribution panel. Get upward to your attic and discover the spot directly above where the distribution panel is. Then employ the same 2.5 in (6.four cm) irksome drill fleck and cut a pigsty through the floor plate.^[12]

   • Attics ordinarily have double plates, so you may accept to drill through 2 blocks of wood to create the pigsty.
   • If you can't find the distribution point, use the measurement you took when y'all drilled the outset hole. Run your tape measure from the aforementioned external wall and discover that distance in the cranium. Drill at this betoken.
   • If your attic has loose fiberglass insulation, wear a dust mask to avoid breathing in any particles.

3. 3

   Drill access holes above the rooms you're running cables to. While nevertheless in the cranium, find the areas above rooms where you need cable access. Employ the 2.five in (6.iv cm) slow drill flake and make holes. The cables volition exit the attic through these holes.^[13]

4. iv

   Mark cutting holes in the rooms that the cables will feed into. Go into each room that you'll run a cablevision to. And then notice the location where you want your cable outlet. So use a ruler and describe a ii in (five.1 cm) by 2 in (5.1 cm) box on the wall. Practice this in each room that you need cable access in.^[14]

   • If you know where the appliances will exist in this room, and so marker the holes most this location. Otherwise, locate them nigh an existing electric outlet.
   • Check for studs behind the wall before picking a location. Make sure yous cut in an area with no studs.

5. five

   Cutting out the box you lot drew on the wall. Use a drywall saw and cut through the lines you drew on the wall. Remove the square of drywall when you've cut all the way around. Repeat this for every room that you're running a cable into.^[15]

   Advertisement

1. 1

   Label the locations for all the wires you're running. Since all cables feed outward from your distribution panel, mark each 1 so you call back its destination. Wrap a piece of white record around each wire. Use permanent marking and write where this cable feeds to.^[sixteen]

   • For example, write Boob tube room, part, and bedroom on the cables.
   • Labeling also makes repairs much easier. If a wire goes bad, you know right away which wire you should pull from the distribution box.

2. two

   Feed your cables up the wall into the attic space. Feeding the wires upwardly and down is unremarkably a 2-person chore. One person pushes the wire through the origin signal and the other pulls through the hole at the destination point. Feed the wire through the hole above the distribution box while someone else pulls the from cranium. Repeat this procedure for every wire you're installing.^[17]

   • Fish tape is the best product for making this job easier. Feed it downwards the hole from the cranium until the person at the distribution box can grab it. Then have them attach the wire to the end of the fish tape. Pull the fish tape upward while the other person feeds the wire and work information technology through the hole in the cranium.
   • Another home remedy if you don't have fish record is taping the wire to a slice of string and using that to pull the wire up.
   • Piece of work cables through the walls gently. Don't pull or jerk them if they go stuck, or y'all could tear them.

3. 3

   Run the wires through the holes above their corresponding rooms. When you've run all the wires up to the attic, then bring each i to the hole that it has to feed down through. Then to the opposite action—have i person feed the cables down through the hole to the destination while another person pulls the cablevision out from the wall.^[18]

   • Apply the fishing record again to make this job easier.
   • Continue the wires out of the way by taping them to the ceiling rafters in the attic. Do not staple them. Staples could harm the wires and also make replacing the wires difficult.

4. 4

   Pull the cables through each wall outlet that you lot cutting. Consummate the cable installation by pulling each cable through the outlet holes yous made. From here, you tin can run coaxial cables to your appliances or install an outlet for ethernet cables.^[19]

   • If you want to hibernate coaxial cables, endeavor installing a wall cover that runs from the outlet to your appliance. These are available from hardware stores.

   Advertisement

Add together New Question

• Question

  What practise I need to pre-wire in a new house?

  

  Drew Hawkins1

  Community Reply

  It can vary from room to room, so showtime past figuring what you desire in each room beginning. Identify which rooms need a cable hookup. Unremarkably, that'll be any room that will have a TV, landline telephone, or figurer. If you lot want to be on the safe side, you tin can run wires into every room, just in case y'all determine yous desire a cable hookup in another room subsequently on. Y'all can salve yourself some trouble. However, if you plan to use wifi for your internet admission, then you won't demand ethernet cables in every room with a computer. Once yous've figured out what rooms you want to wire in the house, yous can start the process of placing a wiring panel and charting the road of the wires from in that location.

• Question

  What kind of wiring is used in new homes?

  

  Drew Hawkins1

  Community Answer

  In that location are unlike wires for dissimilar applications, so when you're wiring a new business firm, you'll need to install the advisable wire for each purpose. Cabling refers to low-voltage cables that provide utilities similar Idiot box, phone, and net service to a home. Commonly, they're coaxial or ethernet cables. It'south also a adept thought to install them when the home is beingness built, rather than having to install them later on. Your safest bet is to really run the cables into every room in the dwelling house. So if you lot decide yous want to add together cable, Tv set, or internet to a room later, the wiring is already in that location and y'all don't have to become through the problem of installing it. No matter what wiring your using, they all connect to the home'southward wiring panel. The best location to place that is somewhere like a basement so it'south out of the way but you tin can also easily run wires to it.

• Question

  What are the iii types of wires in a wire?

  

  Drew Hawkins1

  Community Answer

  A wire with a plug consists of 3 dissimilar wires that work together to allow electricity to menstruation through the wire safely: the live wire, the neutral wire, and the earth or footing wire. In a plug, the live wire is and the neutral wire form the complete excursion. Electricity flows from a power source into the apparatus, gadget, or whatsoever it's plugged into to provide power. Even though the third wire, the ground wire, doesn't really take electricity flow through it, it'south all the same super important. It's a rubber wire that keeps electricity from leaking out and shocking you lot or shorting out your apparatus. Together, these three wires brand up 1 unit that powers your devices.

Ask a Question

200 characters left

Include your email accost to get a message when this question is answered.

Submit

Advertisement

• Recall that this chore is much easier with 2 people. Inquire a friend or family member for some help.

Thanks for submitting a tip for review!

Advertising

• Always make sure the power is off before working with electricity.

• If you aren't confident in your ability to work with electricity safely, bring in a professional for this job instead.

Advertising

Things Yous'll Need

• Power drill
• Boring drill flake
• Ruler
• Tape measure
• Drywall saw
• Gloves
• Goggles
• Dust mask
• Stud finder

Most This Commodity

Thanks to all authors for creating a page that has been read 300,945 times.

Is this article upward to engagement?

Source: https://www.wikihow.com/Install-Cabling-in-a-Pre-Built-Home

Posted by: elderhapat1994.blogspot.com

Share this post